How to Install Fiber Optic Connectors

How to Install Fiber Optic Connectors

Several methods are available for installing fiber optic connectors. These include the Mechanical, Hot Melt, and Pullback methods. You can use any of them as long as you know the specific type of connector you are using and are comfortable performing the installation. However, there are times when you may need some professional help.

Pullback method

The pullback method of fiber optic connector installation is a quick, efficient way to install fiber optic connectors. It is also space-efficient, and in some scenarios, it can negate the need for floor boxes. It requires a skilled technician who pulls the bare fiber out of the cable and threads it into the dwelling space. This method requires field termination, but it is less messy than blowing fiber.

Using the pullback method of fiber installation can be a viable option in a building with sufficient space for the fiber. In certain cases, this method can be used to install fiber optic connectors in plenum spaces or through elevator shafts. It can also be used in places where cable trunking is used to hide cables. There are three viable installation methods: direct fixing, pulling, and pushback.

Hot Melt method

The Hot Melt method of installing fiber optic connectors is a fast and reliable method for securing optical fibers. This method uses a hot-melt adhesive that requires a high temperature to soften and cure. It is not recommended for use with fibers that will be exposed to extreme cold or high heat.

Unlike the epoxy method, the Hot Melt method can be used many times. Once the connectors are installed, they can be reused and can be cooled before being put back into service. It is also possible to reuse connectors and use them in different applications. The finished connectors can be cleaved and air-polished.

To use the Hot Melt method to install fiber optic connector, you should first have the appropriate tool kit. It contains all the test equipment and tools you need to complete the installation. You can get a 120V model and a 230V version. To install the connectors, insert the fiber into the Hot Melt connector and pull it back about 1/16 inch. Then, you can reheat the connector and push it in further.

Chemical method

There are two methods for installing fiber optic connectors: the mechanical and the chemical. The mechanical method is suitable for small connectors, while the chemical method is ideal for larger ones. Both methods require precise alignment and low loss. The fiber optic connectors can be used for cable re-tensioning and break repairs. The first step is to clean the connectors of any coatings. Then, the fiber is cleaved and fused with an electric arc. Once done, the connectors can be polished.

For the second step, it is necessary to clean the connectors with isopropyl alcohol. This is much more effective than using 2-Propanol + water. You can also use canned air to clean the connectors. Once the connectors are clean, you can use a buffer support to prevent them from getting damaged.

Mechanical method

There are two basic types of installation methods for fiber optic connectors – mechanical and chemical. Mechanical methods use a mechanical tool to cleave the fiber and insert it into the connector. Chemical methods use a chemical agent or adhesive to attach the connector and cable to the fiber. Both types can be performed manually or using special tools.

Mechanical methods are generally more expensive than installing fiber optic connectors manually. However, they are more effective and provide better results. They are also easier to install and tend to result in fewer errors. A mechanical method is more flexible than hand-terminating, and is often preferred in campus environments. In addition, a mechanical method is less likely to cause damage than a pre-terminated end.

Optical loss

When installing fiber optic connectors, it is important to consider the optical loss in your installation. Optical loss, also known as attenuation, refers to the amount of optical power that is lost due to any discontinuity in the fiber link. It is often measured in dB and is positive or negative. The goal is to achieve zero optical loss.

Loss is measured in decibels and is caused by a number of factors, including the length of the fiber and its attenuation at each wavelength. For example, if a fiber is 0.3 km long and has a 3.5 dB/km insertion loss at 850 nm, then a connector will have an insertion loss of 0.45 dB. Similarly, a connector will cause insertion loss when it is installed improperly. Fortunately, there are some ways to minimize this loss, but it is important to remember that the amount of optical loss in your installation isn’t zero.

Scroll to Top

Get a Quick Quote!

x